|
TL SERIES
TOP (particleboard core)
Tops shall be constructed of solid, 47 lb., industrial grade
particleboard, surfaced with high pressure plastic laminate and shall be
backed with a phenolic sheet to prevent moisture penetration. Tops are
to be edged with vinyl T molding having a thickness of at least 1/8".
The T molding shall be secured against removal by the use of staples at
regular intervals on the underside of the table top.
TOP (plywood core)
Tops shall be constructed of solid, " thick, AC grade, 7 ply,
exterior glue plywood, surfaced with high pressure plastic laminate and
are to be backed with a phenolic sheet to prevent moisture penetration.
Tops are to be edged with vinyl T molding having a thickness of at least
3/16". The T molding shall be secured against removal by the use of
staples at regular intervals on the under side of the table top.
TOP SUPPORT FRAME
Table tops shall be supported by a formed steel channel frame at least
1-13/16" deep and of 16 gauge steel. The channel shall form a continuous
frame having square corners and welded joints. Frames shall be secured
to the table top with screws placed no greater than 10" apart.
LEG ASSEMBLY
Leg assemblies shall be constructed using a 14 gauge, chrome plated,
formed steel vertical channel, 4" x 1". A full width cross member of
1" diameter, 14 gauge steel tubing shall be welded to the top of the
vertical channel and shall rotate within two, 16 gauge saddle clips that
are securely fastened to the table with 4 screws each. A base of 14
gauge, chrome plated, square steel tubing, 1" x 1", shall be welded to
the bottom of the vertical channel and closed at the ends with internal
plastic caps. Plastic glides, 7/8" x 2", shall be secured to the bottom
of each square tube base with two rivets each. A decorative panel
consisting of a 16 gauge, formed steel, channel frame, 1-13/16" wide,
shall enclose a high pressure plastic laminate panel that is welded to
the upper portion of the leg assembly. The laminate panel shall be
backed up by a 24 gauge, steel sheet.
TLA SERIES
TOP (particleboard core)
Tops shall be constructed of solid, 47 lb., industrial grade
particleboard, surfaced with high pressure plastic laminate and shall be
backed with a phenolic sheet to prevent moisture penetration. Tops are
to be edged with vinyl T molding having a thickness of at least 1/8".
The T molding shall be secured against removal by the use of staples at
regular intervals on the underside of the table top.
TOP (plywood core)
Tops shall be constructed of solid, " thick, AC grade, 7 ply,
exterior glue plywood, surfaced with high pressure plastic laminate and
are to be backed with a phenolic sheet to prevent moisture penetration.
Tops are to be edged with vinyl T molding having a thickness of at least
3/16". The T molding shall be secured against removal by the use of
staples at regular intervals on the under side of the table top.
TOP SUPPORT FRAME
Table tops shall be supported by a formed steel channel frame at least
1-13/16" deep and of 16 gauge steel. The channel shall form a continuous
frame having square corners and welded joints. Frames shall be secured
to the table top with screws placed no greater than 10" apart.
LEG ASSEMBLY
Leg assemblies shall be constructed of a vertical, 14 gauge, chrome
plated, formed steel channel, 4" x 1", which telescopes over a similar
channel of smaller dimension, to allow for vertical adjustment.
Adjustment from 22"-29", 19"-26" or 27"-34", in one inch increments,
shall be possible through the use of a manual spring bolt mechanism. A
full width cross member of 1" diameter, 14 gauge steel tubing shall be
welded to the top of the vertical channel and shall rotate within two,
16 gauge saddle clips that are securely fastened to the table top with 4
screws each. A base of 14 gauge, chrome plated, square steel tubing, 1"
x 1", shall be welded to the bottom of the vertical channel and shall
be closed at the ends with internal plastic caps. Two plastic glides,
7/8" x 2", are secured to the bottom of each square tube base using two
rivets each. A decorative panel consisting of a 16 gauge, formed steel,
channel frame, 1-13/16" wide, enclosing a high pressure plastic laminate
panel is welded to the upper portion of the leg assembly. The laminate
panel shall be backed up by a 24 gauge, steel sheet.
LEG BRACE MECHANISM
Leg braces shall be constructed of at least 7/8" wide x .125" thick,
edge-radiused steel. Braces made of less than 11 gauge steel are not
acceptable. For safety, braces shall lock automatically and remain
locked when the table is in any position during folding and unfolding.
Braces shall be designed and constructed to resist wear from frequent
operation that could prevent the brace from locking the leg securely in
place. Spring actuated devices with case-hardened steel poppits are
preferred. The leg brace pivot bracket shall be secured to the table top
using a minimum of eight fasteners.
METAL FINISH
All metal parts shall be thoroughly cleaned and phosphatized to enhance
paint adhesion. Metal parts are to be finished with a thermofused epoxy
powder coating.
WARRANTY
TL & TLA Series Folding Tables shall be covered by a 1 year warranty.
Plywood top models are covered by a 10-year warranty. |
